If I could post it properly then I was supposed to not seeking help from you here.
Sometimes, urgent needs do not match standards. hope you consider this.
i am not seeking help from home assistant . I am not seeking customer care. I am looking for support to my need. I draw something and shared here. those who are helpful minded and can support me willingly . But those who do not understand and copying , pasting rules here will receive a big thank you from me . but situation is same , i need help from experts. Thanks a lot for your time in my post.
However, when many people read the title, and then read the body, they’ll ignore the post because it looks like you’re just using the title to get attention.
Without marking up your code as code, nobody can tell what the problems may be. It’s literally unreadable.
No one can support unformatted non-indented code. I am trying to help you getting help, but you seem immune to assistance. Stop being an ass.
? “automation old temperature_cold”
:
action:
-
entity_id: switch.YOUR_AC_OFF_SWITCH
service: switch.turn_on
alias: “Stop the cooling”
condition:
condition: template
value_template: “{{ states.sensor.YOUR_TEMPERATURE_SENSOR.state | float - states.input_slider.stue_temperatur.state | float < -1 }}”
trigger:
minutes: /05
platform: time
seconds: 0
? “automation old temperature_high”
:
action:
-
entity_id: switch.YOUR_POWERFUL_MODE_SWITCH
service: switch.turn_on
alias: “Full cooling”
condition:
condition: template
value_template: “{{ states.sensor.YOUR_TEMPERATURE_SENSOR.state | float - states.input_slider.desired_temperature.state | float > 1 }}”
trigger:
minutes: /05
platform: time
seconds: 0
? “automation old temperature_normal”
:
action:
-
entity_id: switch.YOUR_QUIET_MODE_SWITCH
service: switch.turn_on
alias: “Gentle cooling”
condition:
condition: template
value_template: “{{ states.sensor.YOUR_TEMPERATURE_SENSOR.state | float - states.input_slider.desired_temperature.state | float > -1 }}”
trigger:
minutes: /05
platform: time
seconds: 0
input_slider:
desired_temperature:
icon: “mdi:thermometer”
initial: 23
max: 24
min: 22
name: “Desired temperature”
step: 1
Three backticks ( ``` ) above and below the YAML sections.
Please read this before making another post, especially section 11.
Format it properlySpacing is critical in YAML, and if you just throw the code on the page then it’ll look ugly and nobody will know if the problem is because of spacing. We need you to use code blocks and appropriate markup.
For example, this is easy to read and it is obvious if the spacing is correct:
# Turn off lights when everybody leaves the house
- alias: 'Rule 2 - Away Mode'
trigger:
platform: state
entity_id: group.all_devices
to: 'not_home'
action:
service: light.turn_off
entity_id: group.all_lights
This however, not so much:
Full details are in that link , but in brief you wrap your block in three backticks (```), like this:
# Turn off lights when everybody leaves the house
- alias: 'Rule 2 - Away Mode'
trigger:
platform: state
entity_id: group.all_devices
to: 'not_home'
action:
service: light.turn_off
entity_id: group.all_lights
? “automation old temperature_cold”
:
action:
-
entity_id: switch.YOUR_AC_OFF_SWITCH
service: switch.turn_on
alias: “Stop the cooling”
condition:
condition: template
value_template: “{{ states.sensor.YOUR_TEMPERATURE_SENSOR.state | float - states.input_slider.stue_temperatur.state | float < -1 }}”
trigger:
minutes: /05
platform: time
seconds: 0
? “automation old temperature_high”
:
action:
-
entity_id: switch.YOUR_POWERFUL_MODE_SWITCH
service: switch.turn_on
alias: “Full cooling”
condition:
condition: template
value_template: “{{ states.sensor.YOUR_TEMPERATURE_SENSOR.state | float - states.input_slider.desired_temperature.state | float > 1 }}”
trigger:
minutes: /05
platform: time
seconds: 0
? “automation old temperature_normal”
:
action:
-
entity_id: switch.YOUR_QUIET_MODE_SWITCH
service: switch.turn_on
alias: “Gentle cooling”
condition:
condition: template
value_template: “{{ states.sensor.YOUR_TEMPERATURE_SENSOR.state | float - states.input_slider.desired_temperature.state | float > -1 }}”
trigger:
minutes: /05
platform: time
seconds: 0
input_slider:
desired_temperature:
icon: “mdi:thermometer”
initial: 23
max: 24
min: 22
name: “Desired temperature”
step: 1
Just damn well stop this idiocy.
than show your brilliance .
You have been shown how to post your logs and directed to the instructions at least 3 times. You ignore us each time. You are frustrating beyond belief.
READ
THE
POST
I reiterate that is is hard to help when you haven’t formatted your code properly, but all entity id’s are lower case in home assistant, so there are multiple errors of that nature in your code.
thank you . i will correct it. this is still draft version.
“it should turn On the AC climate.stuen with the following setting —hvac_modes:cool ,temperature: 22 ,fan_mode: 5, swing_mode: 2, vane_horizontal: 1,left vane_vertical: 2 2 — turn off”--------------i have to add this requirements in my script. but i am not understanding how to these conditions correctly.
We still cannot help if you don’t post your code properly. I can’t help any more.
alias: Turn off your air conditioner automatically
initial_state: true
trigger:
platform: numeric_state
entity_id: switch.bedroom_airconditioner
value_template: “{{ state.attributes.current_temperature }}”
below: 22
condition:
condition: state
entity_id: switch.bedroom_airconditioner
state: ‘on’
action:
alias: Turn on your air conditioner automatically
initial_state: true
trigger:
platform: numeric_state
entity_id: switch.bedroom_airconditioner
value_template: “{{ state.attributes.current_temperature }}”
above: 24
condition:
condition: state
entity_id: switch.bedroom_airconditioner
state: ‘off’
action:
How difficult is it to copy your code here in the forum, highlight the qhole text and press this sign at the top </> ???
Everyone, I understand your frustrations but please don’t get upset and belittle him. Just move on. In time OP will figure this out and we can help when that happens.
@Sami1 take a look here https://www.home-assistant.io/integrations/climate/
I think you are (effectively) asking how to set the various parameters in your climate component.
Use the services listed on that page to set those parameters.
As far as using services in the action: of your automation, see https://www.home-assistant.io/docs/automation/action/. You could probably also use a scene, but I haven’t tried that with a climate component.