already posted some posts above
Hello,
Power Flow Card Plus no longer works with Huawei solar integration since the mushroom update???
Am I alone???
Hi Ribe
looks good and i am intrested.
can you pleas send me the card code?
Love
BaD
Works fine here, patched to latest HA/OS etc levels also.
Look at Sunsynk Power Flow Card also.
Après retour vers une VM de sauvegarde, la mise à jour de Mushroom n’a pas planté Power Flow Card Plus.
Thank you I already searched hours for this
Hi,
I have Luna connected thru the inverter. And now, returned energy is shown as solar production at night. Is it posible to separate sensors?
Hello!
I have 2 inverters, a 10 kW and a 6 kW. Both inverters are connected to 2 x 5 kWh batteries, so each inverter has its own dedicated battery. The 10 kW inverter controls the system, and battery charging is prioritized. When the house is consuming power, it is supplied via the battery. However, until the battery is fully charged, the solar energy production is not displayed, and the minus value appears twice on the energy panel, but only there. What can I do to fix this? Also, solar production appears at night too. :)))
Needless to say, the house’s consumption is also displayed incorrectly because of this. It only shows the real consumption correctly around midnight.
I have a problem with the values coming from the smart meter. In particular, the house consumption shows the energy used. I would have expected to see power used. Is it possible to get that info?
And another question - the values for the power meter updates very slowly, sometimes more than an hour between updates. Is it possible to improve that somehow? I’m currently connected through the Sdongle, as I could not get the connection to the Inverter’s AP to work. I can connect, and port 6607 is open, but I do not get any data.
Any help i highly appreciated.
It looks like this template solved the problem. I looked up an example for this earlier.
I love this forum, you can always find alternative solutions here 
template:
- sensor:
# 6PV second battery pack
- name: 6KTL Total PV
#friendly_name: "PV Energy"
unique_id: "PV Energy 6"
state: "{{ (states('sensor.sun2000_6ktl_total_yield') | float) - (states('sensor.luna2000_battery_2_total_discharge') | float) + (states('sensor.luna2000_battery_2_total_charge') | float)}}"
device_class: energy
state_class: total
unit_of_measurement: kWh
- name: 6KTL Daily PV
#friendly_name: "PV Energy daily"
unique_id: "PV Energy daily 6"
state: "{{ (states('sensor.sun2000_6ktl_daily_yield') | float) - (states('sensor.luna2000_battery_2_day_discharge') | float) + (states('sensor.luna2000_battery_2_day_charge') | float)}}"
device_class: energy
state_class: total
unit_of_measurement: kWh
# 10PV first battery pack
- name: 10KTL Total PV
#friendly_name: "PV Energy"
unique_id: "PV Energy 10"
state: "{{ (states('sensor.sun2000_10ktl_total_yield') | float) - (states('sensor.luna2000_battery_total_discharge') | float) + (states('sensor.luna2000_battery_total_charge') | float)}}"
device_class: energy
state_class: total
unit_of_measurement: kWh
- name: 10KTL Daily PV
#friendly_name: "PV Energy daily"
unique_id: "PV Energy daily 10"
state: "{{ (states('sensor.sun2000_10ktl_daily_yield') | float) - (states('sensor.luna2000_battery_day_discharge') | float) + (states('sensor.luna2000_battery_day_charge') | float)}}"
device_class: energy
state_class: total
unit_of_measurement: kWh
Hi!
I use Homewizard instead of the Power Meter because it’s not accurate for me either; sometimes it shows a difference of 2-3 kWh compared to the HW, which is directly connected to the electricity meter via the P1 port. I’ve been using it for 2 years without any issues. I’ve already tested to see if everything goes through the Huawei Power Meter, and it seems that it does, but the data still differs. Since the electricity provider uses the electricity meter as a reference, I prefer using the HW.
Do you do some calculations on top of that? My electricity meter only shows import and export. But the actual consumption would something along the line of (solar power + import + battery discharge) - (export + battery charge).
But then it becomes a bit tricky if I charge the battery from imported electricity, or discharge the battery for export.
And the power values from the inverter and power meter have such slow update frequency that it becomes very inaccurate.
Yes, I used exactly the code you mentioned above. I subtract the battery charge, if that’s what you’re referring to. I got the example from here.
the only way i did it is:
manual ip in HA lan conected to router 192.168.1.1 [minipc lan]
and automat ip conected with HA on huwaei hotspot 192.168.200.1 [minipc wifi dongle]
host: 192.168.200.1
port 6607
so it seems its about vlans management the problems when u have FE dongle conected to invertor by lan it gets vlan 1 : 192.168.1.1 as internet
when conecting by minipc dongle to invertors hotspot u get vlan 200: 192.168.200.1.
else try remove fe dongle and use invertor’s wifi hostspot.
have fun guys
Hi everyone,
I’m David and I’m new to Home Assistant. I’m excited to learn more about this platform and connect with other users.
Hello Home Assistant community,
I’m having some trouble adding a second Huawei inverter to my HA setup. I’ve already integrated one inverter using a dongle and it’s working fine.
The second inverter doesn’t have a dongle, but I can access it via its IP address. However, when I try to add it to HA using the same integration method as the first one, I get a connection error.
Thanks for your help!
“If you want to connect through the dongle, then you need to put in the two slave IDs as Thijs has said above. In a lot of cases it is either 0 and 1, 1 and 2 or 1 and 16. However, if you want to find out which slave ids your system has, then you need to login to the inverter using the Fusionsolar app and the internal AP. There you can see the slave id under the communication settings.”
good user and pasword
Unexpected error???
It worked very well 2 weeks but after the last homeassistant update- out of order…
Tried to delete and reinstall, no results.
Can you share your dashboard please.
Thx
Assuming your talking about two inverters in the same location / home setup?
If so, then you shouldn’t be looking to ‘add’ the second inverter via LAN / IP address, you need to lookup the RS485 networking section of the inverters manual.
In there you’ll see that you should be wiring the secondary inverter into the primary inverter using the RS485 connectors. When thats done correctly and configured in FusionSolar, you should then go to the FusionSolar Portal and you’ll see the site with the sDongle and below that the two inverters should show.
In HA you then just need to reconfigure the Huawei intetgration (WLCRS) and refer to the Wiki section on Github for WLCRS, that refers to the ID numbers you need to use (by default will probably be ‘1,2’) that should be entered, at which point the integration should query your setup and see the two inverters (and any batteries / optimisers also).