thanks I dod’t notice the aliexpress link
Just took delivery this morning from Ali. Is there any way of telling if it’s the B version just by looking at it or do I need to power it up to find out
Thanks
Sweet! Thanks for sharing. How is the HD2410 mounted?
Do I understand it correctly, if I set up the LD2410 sensor according to my idea and then use another esp module where I just insert a simple configuration of the binary sensor, will it work with the settings I made on the test board?
Mine has just arrived. the Bluetooth version connects to an app. I wonder if HA can add this integration to access the Bluetooth directly, without need for an ESP32/8266
1 Like
Ho I read it for the above HLK-LD2410 YAML:
Red: Is VCC: +5V
Black: Is GND: GND
Yellow: Is UART Rx → GPIO18 (TX from ESP)
Green: Is UART Tx → GPIO23 (RX from ESP)
Blue: Is OUT: GPIO5
3 Likes
great idea - would love to hear if someone manages this.
Does anyone have issues with programming the ld2410 ? I have everything wired up and using the code from crlogics, I can read sensor data (the binary one) and also see stats if I toggle that on in the webui, which leads me to believe the wiring is fine.
However when I adjust the detection distance it doesn’t seem to do anything I have sensing set to 6m, yet it’s only picking me up at about 50cm - 1m… If I reboot the ESP the detection distance changed back to 0.75m in the HA UI, is that supposed to happen?
Yes, the same problem that has gone so far that currently the sensor does not respond and remains in the off state. I’m afraid he got hurt in some way. I also use the LD1115H sensor and it works fine including the settings.
Hmm thanks, would be interesting to know if crlogic ever encountered anything like this as the write up doesn’t appear to suggest any problem configuring the module.
Hopefully it can be solved, I have 10 of these sat on my desk waiting to be setup 
Code works on my working LD2410. I also have another that doesn’t report via serial for my code or HLK’s app. Tiny headers are challenging if you are soldering.
Thanks, I assume when looking from HA the sliders for distance and other settings shouldn’t be resetting back to default after restarting the ESP? (mine go back to 0.75m max distance, 0.0 motion hold and 10.0 sensitivity)
Check that you can see UART data being received. Without it, code can do nothing for ya 
Yes, if I switch on the toggle ‘show_target_stats’ on the web interface I can see data from the module, as far as I understand this info is from the UART as the other pin on the board is simply a high/low for if presence is detected?
eg, I see this;
13:38:42 [D] [sensor:127]
'movingTargetEnergy': Sending state 94.00000 % with 0 decimals of accuracy
13:38:42 [D] [sensor:127]
'stillTargetEnergy': Sending state 41.00000 % with 0 decimals of accuracy
13:38:42 [D] [binary_sensor:036]
'mmwave_presence_ld2410': Sending state ON
Do you have your LD2410 powered separately? - Mine is coming straight from the 5v of the ESP32.
Can you turn on UART debugging in both directions to ensure you are sending and receiving ok? There will be a response from the sensor when changing sensor values.
Not sure if anybody posted before, been busy with work. HLK just emailed me the English version of the app for LD2410B for Android
Can download it here-> WeTransfer - Send Large Files & Share Photos Online - Up to 2GB Free
Need to rename it to .apk, you will be ask to update after installation.
1 Like
Thanks for the tip, just added that to the yaml and deployed it - after deploying the webui showed the saved data from the module and when I changed settings I could see the UART commands and no errors. Then I commented the debug line deployed again, and after it came back all the settings were showing in the webui / HA as the defaults again 
I uncommented the debug line and deployed again and then it showed the saved settings again! So confused… will try and do some more digging with it tomorrow.