No, still no luck. Sorry.
I’ll note I was able to get service calls for my dinky onvif camera to do pan/tilt via calls to:
service: onvif.ptz
and data like:
entity_id: all
tilt: DOWN
speed: 1
distance: 0.3
move_mode: ContinuousMove
Turns out that “move_mode” is important for my cam and some cameras only support ContinuousMove apparently. YMMV.
Started a cute panel for it, I’m sure it’s been done plenty, but I like it:
type: picture-glance
entities:
- entity: camera.garage_tilt
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.garage_tilt
pan: LEFT
speed: 1
distance: 0.3
move_mode: ContinuousMove
name: Pan Left
show_state: false
icon: 'mdi:arrow-left'
show_icon: true
- entity: camera.garage_tilt
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.garage_tilt
tilt: UP
speed: 1
distance: 0.3
move_mode: ContinuousMove
name: Tilt Up
icon: 'mdi:arrow-up'
- entity: camera.garage_tilt
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.garage_tilt
tilt: DOWN
speed: 1
distance: 0.3
move_mode: ContinuousMove
name: Tilt Down
icon: 'mdi:arrow-down'
- entity: camera.garage_tilt
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.garage_tilt
pan: RIGHT
speed: 1
distance: 0.3
move_mode: ContinuousMove
name: Pan Right
icon: 'mdi:arrow-right'
show_icon: true
camera_image: camera.garage_tilt
camera_view: live
Full panel with little pan/tilt buttons at the bottom.
Hi Mate
I have just used your card code for my onvif camera and it works relatively well, however…
When I click any of the arrows, it does the whole circle, until it ends , also I’m getting a message: “failed to call service onvif/ptz missing attribute”
Not sure what I’m missing.
I would be happy if I would have more control over the pan and tilt
Thanks
Thank you for this card setup. I just added my Escam G2 to HA via ONVIF integration (in the past I was using it as a general camera) and when I saw that I can trigger these movements, I started to search for a way to add these buttons to the card. Your solution works perfectly for my needs. Thank you for sharing!
Tanks a lot.!
It works like a charm with my new Reolink E1 Pro !
Regards,
Jeff
Hi, i’m getting ‘NoneType’ object has no attribute ‘continuous’ to.
:S
I have a Sunba 405-ECO V2 PTZ and the below has worked for me with the addition of 2 presets. A short delay as the ONVIF feed is not truly live so avoid many button pushes.
RAW configuration fro HA
title: PTZ
views:
- title: test
path: test
badges: []
cards:
- type: picture-glance
title: Kitchen
image: 'https://demo.home-assistant.io/stub_config/kitchen.png'
entities:
- entity: camera.ptz_profile_000
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.ptz_profile_000
pan: LEFT
speed: 0.5
distance: 0.5
move_mode: ContinuousMove
name: Pan Left
show_state: false
icon: 'mdi:arrow-left'
show_icon: true
- entity: camera.ptz_profile_000
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.ptz_profile_000
tilt: UP
speed: 0.5
distance: 0.5
move_mode: ContinuousMove
name: Pan Up
show_state: false
icon: 'mdi:arrow-up'
show_icon: true
- entity: camera.ptz_profile_000
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.ptz_profile_000
tilt: DOWN
speed: 0.5
distance: 0.5
move_mode: ContinuousMove
name: Pan Down
show_state: false
icon: 'mdi:arrow-down'
show_icon: true
- entity: camera.ptz_profile_000
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.ptz_profile_000
pan: RIGHT
speed: 0.5
distance: 0.5
move_mode: ContinuousMove
name: Pan Right
show_state: false
icon: 'mdi:arrow-right'
show_icon: true
- entity: camera.ptz_profile_000
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.ptz_profile_000
preset: 1
speed: 0.5
distance: 0.5
move_mode: GotoPreset
name: Preset 1
show_state: false
icon: 'mdi:numeric-1-box'
show_icon: true
- entity: camera.ptz_profile_000
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: camera.ptz_profile_000
preset: 2
speed: 0.5
distance: 0.5
move_mode: GotoPreset
name: Preset 2
show_state: false
icon: 'mdi:numeric-2-box'
show_icon: true
camera_image: camera.ptz_profile_000
camera_view: live
I can’t seem to get GotoPreset
to work, ContinuousMove
works fine - but is useless if I have to click like an idiot to get to my presets. I can access these fine with MotionEye and Keyboard Maestro, so I know its not an issue with the camera’s ability to reference presets. An idea what could be wrong?
Can you share the logs for when you run the service?
As well as the data you are using for it?
I haven’t actually put it in the config yet, only tested with the dev tool. As I said though, ContinuousMove works well, just GotoPreset that won’t fire anything.
Where would I find the logs?
Ok, so - simple button, simple code. Preset 6 pans fine from Keyboard Maestro and MotionEye.
type: entity
entity: camera.balcony_profile0
tap_action:
action: call-service
service: onvif.ptz
service_data:
entity_id: ccamera.balcony_profile0
pan: RIGHT
preset: 6
speed: 1
distance: 1
continuous_duration: 1
move_mode: GotoPreset
name: Preset 6
show_state: false
icon: 'mdi:numeric-6-box'
show_icon: true
Found the log entry:
Last logged: 12:55:34 PM
PTZ preset '6' does not exist on device 'Balcony'. Available Presets: preset0, preset1, preset2, preset3, preset4, preset5, preset6, preset7, preset8
ok so try set it like this :
preset: preset6
Hello @olijouve!
I finally figured it out late last night. I got it working doing exactly that preset: preset#
… though I initially tried that immediately after seeing that mentioned in the logs and it was throwing me a very strange error - one that Google couldn’t help with;
“Nousd”? What the hell is “Nousd”?! I Googled like crazy and found nothing. It wasn’t until I figured out that the preset numbers stored in the camera are different than those on my Security Spy or Keyboard Maestro references. They are stored in the order they are created. So trying another preset number worked, anything other than “preset6”.
…I think “Nousd” means “Un-used”.
Anyhow, thanks for your help!
I just copied and pasted PoorMattie’s config and replaced the camera entity with mine. Works perfectly straight away. thank you!
Hello how did you do for the preset because I can not do it ?
entity_id: camera.ipcam_profile1_2
pan: RIGHT
distance: 1
speed: 0.5
continuous_duration: 0.5
preset: position 1
move_mode: GotoPreset
here is the photo of my presets
This code works amazing!
The big question is though, can you also add audio from the camera in it?
Hi guys, I am ultra noob in HA can anybody write me, where I am supposted to write that code? In configuration.yaml?
Ondrej. Tienes que crear una tarjeta en la pantalla inicial de Home Assistant.
Gracias por vuestros ejemplos.
Lo intento y ya os contaré.
(Mi ingles es pobre)
Many thanks for that. Works a treat on my Wansview W9.