Is it possible to retrieve the existing codes from the locks in HA or would we effectively need to start over and enter the codes in HA again?
Depends on your lock.
I have the Schlage BE469.
I don’t believe that lock allows you to read the code slots.
Ok, thank you.
I’m having some strange behavior from the Notify_Front_Door_Lock automation and trying to figure out how I can trouble shoot. I think it’s coming from 2 lines in the front_door_report sensor which I can’t quite figure out how they work.
PROBLEM:
I’m getting duplicate notifications about 6 minutes apart when the door is unlocked with a code. When the door is first unlocked I get the correct notification with accurate front_door_report information.
After 5 minutes of the door being closed I have an automation which locks the deadbolt and I can see the front_door_report sensor correctly changing to “HA lock” but after 33 seconds it changes back to the original report showing who unlocked the door with the code which (I think) then re-triggers the notify automation.
Any ideas on what I should be looking for / where I might find the problem? Thanks.
Looking in the Logbook I see the following:
Notify on Unlock (Front Door) has been triggered by sensor.front_door_report via template
9:00:00 AM - 1 hour ago
Front Door Report changed to Keypad Unlock with Code 3 (ASegel)
9:00:00 AM - 1 hour ago
Front Door Report changed to HA Lock by Front Door auto lock
8:59:27 AM - 1 hour ago
Front Door was locked by Front Door auto lock
8:59:27 AM - 1 hour ago
Front Door auto lock has been triggered by state of binary_sensor.front_door_open_sensor
8:59:24 AM - 1 hour ago
Time changed to 08:59
8:59:00 AM - 1 hour ago
Notify on Unlock (Front Door) has been triggered by sensor.front_door_report via template
8:54:17 AM - 1 hour ago
Front Door was unlocked
8:54:17 AM - 1 hour ago
One strange finding is that at 8:54:17 I see front_door_report changing states in the History but not the logbook. Not sure why.
Notify Automation:
- alias: Notify on Unlock (Front Door)
initial_state: true
trigger:
- platform: template
value_template: "{{ states.sensor.front_door_report.state.lower().startswith('keypad unlock') }}"
condition:
- condition: state
entity_id: 'input_boolean.allow_zwave_automation_execution'
state: 'on'
action:
- delay:
seconds: 1
# This will set a a friendly name of whoever unlocked the door to input_text.front_door_code, use in other automations if you wish
- service: input_text.set_value
data_template:
entity_id: input_text.front_door_code
value: >
{% set number = states('sensor.front_door_deadbolt_alarm_level') %}
{% set entity_id = 'input_text.door_keypad_' + number + '_name' %}
{% set user = 'Master' if number == '0' else states(entity_id) %}
{{ user }}
- condition: template
value_template: >-
{% set code_used = states('sensor.front_door_deadbolt_alarm_level') %}
{% set notify_input_object_id = 'code_' ~ code_used ~ '_notify' %}
{{ states['input_boolean'][notify_input_object_id].state == 'on' }}
- service: notify.mobile_app_garrett_iphone11
data_template:
title: "Front Door Unlocked"
message: >-
by {{ states.input_text.front_door_code.state }} at {{ as_timestamp (now()) | timestamp_custom('%I:%M %p') }}
front_door_report sensor: (only the 2 lines in question)
{% set alarm_type_value = '24' if (as_timestamp(now())-as_timestamp(states.lock.front_door.last_changed)) < 15 and (as_timestamp(now())-as_timestamp(states.sensor.front_door_deadbolt_alarm_type.last_changed)) > 15 and (states.lock.front_door.state) == 'locked' else alarm_type_value %}
{% set alarm_type_value = '25' if (as_timestamp(now())-as_timestamp(states.lock.front_door.last_changed)) < 15 and (as_timestamp(now())-as_timestamp(states.sensor.front_door_deadbolt_alarm_type.last_changed)) > 15 and (states.lock.front_door.state) == 'unlocked' else alarm_type_value %}
front_door_report sensor: (all lines)
sensor:
- platform: template
sensors:
front_door_report:
friendly_name: 'Front Door Report'
value_template: >
{% set number = states('sensor.front_door_deadbolt_alarm_level') %}
{% set alarm_type_value = states('sensor.front_door_deadbolt_alarm_type') %}
{% set entity_id = 'input_text.door_keypad_' + number + '_name' %}
{% set user = 'Master' if number == '0' else states(entity_id) %}
{% set alarm_type_value = '24' if (as_timestamp(now())-as_timestamp(states.lock.front_door.last_changed)) < 15 and (as_timestamp(now())-as_timestamp(states.sensor.front_door_deadbolt_alarm_type.last_changed)) > 15 and (states.lock.front_door.state) == 'locked' else alarm_type_value %}
{% set alarm_type_value = '25' if (as_timestamp(now())-as_timestamp(states.lock.front_door.last_changed)) < 15 and (as_timestamp(now())-as_timestamp(states.sensor.front_door_deadbolt_alarm_type.last_changed)) > 15 and (states.lock.front_door.state) == 'unlocked' else alarm_type_value %}
{% set alarm_type_general_actions = {
'0':'No Status Reported',
'9':'Jammed',
'17':'Jammed',
'21':'Manual Lock',
'22':'Manual Unlock',
'23':'Jammed',
'24':'HA Lock',
'25':'HA Unlock',
'26':'Jammed',
'27':'Auto Lock',
'32':'All Codes Deleted',
'161':'Bad Code Entered',
'167':'Battery Low',
'168':'Battery Critical',
'169':'Battery Too Low To Operate Lock' } %}
{% set alarm_type_lock_actions = {
'18':'Keypad Lock',
'19':'Keypad Unlock',
'162':'Lock Code Attempt Outside of Schedule' } %}
{% set alarm_type_code_actions = {
'33':'Code Deleted',
'112':'Code Changed',
'113':'Duplicate Code' } %}
{% if alarm_type_value in alarm_type_code_actions %}
{{ alarm_type_code_actions[alarm_type_value] }} (Code {{ number}})
{% elif alarm_type_value in alarm_type_lock_actions and number == '0' %}
{{ alarm_type_lock_actions[alarm_type_value] }} with Schlage Button
{% elif alarm_type_value in alarm_type_lock_actions %}
{{ alarm_type_lock_actions[alarm_type_value] }} with Code {{ number }} ({{ user }})
{% elif alarm_type_value in alarm_type_general_actions %}
{{ alarm_type_general_actions[alarm_type_value] }}
{% else %}
Unknown Alarm Type Value {{ states('sensor.front_door_deadbolt_alarm_type') }}
{% endif %}
auto_lock automation:
- id: '1609386460351'
alias: Front Door auto lock
description: ''
trigger:
- platform: state
entity_id: binary_sensor.front_door_open_sensor
to: 'off'
for: 00:05:00
condition:
- condition: device
device_id: b7c9d09c2276e372b9da7db339f76443
domain: lock
entity_id: lock.front_door
type: is_unlocked
action:
- service: lock.lock
data: {}
entity_id: lock.front_door
mode: single
I’m having two issues with implementing… and keep in mind, I’m brand-new to this:
- I don’t know why
input_boolean.allow_zwave_automation_executionis preventing this from running. My OZW network is running & healthy. - I renamed both of my two Kwikset 914 locks when I added them. I don’t know why one is recognized and the other isn’t… and I don’t know what to rename the references in the dashboard to get the 2nd lock to work. I deleted the third one in the raw editor.
Any ideas?
Is there a way to roll this install back? I’ve removed the *.yaml files from the packages folder and deleted the Lovelace dashboard… but the timer, text, input select, etc. entities still remain. It doesn’t appear to be possible to remove them via the UI.
Thanks!
Restart HA core. It won’t delete them until it re-initializes the helpers.
1 Like
Thanks. I did a reboot of the RPi and they remained… so I just went through and manually deleted them one-by-one.
1 Like
sorry if this is mentioned somewhere else, but does this work with Zwave JS now that it is available in add-ons?
I liked this one much better, as I have many locks and User-based is more efficient than Lock-based.
If a user want to change a code, your’s is a single change - Key master I have to change in every lock…
Unless there is a method to use Keymaster I’m unaware of.
The parent/child lock setup syncs codes across locks.
I was wondering the same. I was hoping I would just have to rename the entities to match but entities belonging to the devices completely changed after migrating to Z-Wave JS. The enabled entities when I switched were binary sensors. There were some disabled sensor entities that I enabled and renamed to match the old package (along with updating from zwave to zwave_js in the package and lovelace) but I couldn’t get it to work.
I love this lock package and it is the main reason I bought additional locks for all doors. I restored a previous snapshot for now but I really hope there is a way to get it to work with Z-Wave JS.
I have the parent/child setup, but not sure that fits my (highly unique) use case. I have 5 bedrooms with only 4 kids living at home ATM.
My youngest is on the ASD, so we have locks on most doors to keep him safe and out of older kids’ rooms and unable to elope easily. Son is a fucking ninja, so automation has developed into a must-have vs neat-to-have.
I loved the Lock Manager on Hubitat, where I only managed Users/Codes, and clicked which locks to assign them to. That way, older/adult children, therapists, maids, etc have access to every lock, younger ones have access to their own and required ones, etc.
Anyway to get similar functionality with this awesome app?
I was wondering if there was an update to this for the depreciation of entity_id?
If anyone has done this, I’d be really happy if you’d post it. I’ve been working on it for a bit but at this point it might be beyond what I know how to do.
Thanks.
I would recommend that you look at KeyMaster or Lock Code Manager as those are actively maintained integrations that work for managing a lock
1 Like
Thanks. I’ll give them a try.
LCM is the cleaner of the two, but it’s also more alpha in a lot of ways.
Keymaster generates a lot of entities and automations, so be warned.
If you’re trying to do something with Airbnb or other STR platforms then you would want to use Keymaster as Rental Control presently only integrates with Keymaster
I was looking at that and I was thinking that I’d need Keymaster. I’ll give it a try. Still working on the removal of entities and helpers this generated. I’ve removed the packages but those things are still there. I’ve restarted and did a hard refresh of the browser as well.