433toMQTTto433 Gateway Device List

Hardware
181

Works fine , and if you install alixpress android app, is more cheaper

each 4.36 eur

182

These Aukey outlets work.

183

So on the github page it says the Sonoff RF Bridge works with this firmware - does it also allow transmitting codes?

184

hello,

yes both, receiving and transmitting, here is the user guide

185

Excellent. I was using Tasmota’s Firmware and after a lot of back and forth it was marked as no transmit.

Any ideas why I am getting this compile error?

C:\Users\simon\Downloads\OpenMQTTGateway\OpenMQTTGateway/ZgatewayRF.ino:54: undefined reference to `RCSwitch::send(unsigned long, unsigned int)'

sketch\OpenMQTTGateway.ino.cpp.o: In function `MQTTtoRF(char*, char*)':

C:\Users\simon\Downloads\OpenMQTTGateway\OpenMQTTGateway/ZgatewayRF.ino:90: undefined reference to `RCSwitch::send(unsigned long, unsigned int)'

C:\Users\simon\Downloads\OpenMQTTGateway\OpenMQTTGateway/ZgatewayRF.ino:98: undefined reference to `RCSwitch::send(unsigned long, unsigned int)'

collect2.exe: error: ld returned 1 exit status

exit status 1
Error compiling for board Generic ESP8266 Module.
186

You should comment the following lines on user_config.h:
//#define ZgatewayIR
//#include “config_IR.h”
//#define ZgatewayBT
//#include “config_BT.h”
//#define ZgatewayRF
//#include “config_RF.h”

and uncomment these ones:
#define ZgatewaySRFB
#include “config_SRFB.h”

187

you should compile with ESP8285

188

Is there any way to handle a motion sensor that only sends a message on motion detected, but not on motion off? I don’t know how to handle that in home assistant config. If I don’t, home assistant just says motion is on always.

189

create an automation that sets it to off after 1 second.

190

cheap chinese motion sensor, only send message when movements are detected

191

Thanks, I’ll do that!

192

Thanks for your not helpful reply.

193

You’re welcome

194

that are the better ones.

195

Just got these Digoo door sensors, they work but only transmit on open. The also look to be identical to the Vstarcam door sensors (AF117) , though I have not tested those.
https://m.banggood.com/Digoo-DG-HOSA-433MHz-Window-Door-Sensor-PIR-Detector-Wireless-Remote-Controller-External-Siren-p-1163239.html

196

Hello, I have one PIR Kerui P817, but I only get the “on” state topic, in HA I only have the state on triggered!
How I can fix this?

197

Hi @canossa,

Considering you have set the default topic for the RF gateway, you should have now a binary sensor, with “on” payload sent by the PIR sensor (“xxxxxx” in my example below). An “off” payload needs to be sent and the easiest way of doing it is to concatenate “off” to original payload (classic “on” and “off” could be used for payload but it would require setting up an additional sensor and automation).

The automation included below would reset the binary second after 5 seconds the initial “on” payload (“xxxxxx”) has been received. Replace payload with your code and pirx with a human readable value.

#Binary sensor
- platform: mqtt
  state_topic: 'home/433toMQTT'
  name: 'PIRx'
  payload_on: 'xxxxxx'
  payload_off: 'xxxxxxoff'
  device_class: motion

#Automation
- alias: Reset PIRx state
  initial_state: 'on'
  trigger:
    - platform: state
      entity_id: binary_sensor.pirx
      to: 'on'
      for: 
         seconds: 5
  action:
    - service: mqtt.publish
      data:
        topic: "home/433toMQTT"
        payload: "xxxxxxoff"
2 Likes
198

Dear, does HT6P20B transmission protocol support? I am interested to implement it with an ESP LoLin for the PPA alarm sensors that I already have installed. Are there already the probes?

199

Thanks, work fine!

200

Got some of these wall switches working:

https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180117181103&SearchText=century+aoke+86+wall+panel+remote