I tried for about 4 days until I succeeded on one on the third day.
But after running for about 26 hours, I couldn’t read the data.
Other same hardware and software couldn’t read it either.
I got a bit crashed. I need help.
My English is not very good
esphome:
name: esp32-11
friendly_name: esp32-11
esp32:
board: esp32-c3-devkitm-1
# Enable logging
logger:
# Enable Home Assistant API
api:
encryption:
key: "p55hLere6La5DK+d7+16NTOgWLueXYwyQqnTZL/9G6U="
ota:
password: "12c41be6cc3446e5fa94b2f858acf1e5"
wifi:
ssid: llong
password: "52070304"
# Enable fallback hotspot (captive portal) in case wifi connection fails
ap:
ssid: "Esp32-11 Fallback Hotspot"
password: "3LQqldhDp4Cf"
captive_portal:
#i2c:
#sda: 21
#scl: 20
#scan: true
#id: bus_a
uart:
id: ld2410_uart
tx_pin: GPIO21
rx_pin: GPIO20
baud_rate: 256000
parity: NONE
stop_bits: 1
ld2410:
uart_id: ld2410_uart
throttle: 2000ms
id: ld2410_comp
select:
- platform: ld2410
distance_resolution:
name: distance resolution
baud_rate:
name: baud rate
light_function:
name: light function
out_pin_level:
name: out pin level
button:
- platform: ld2410
factory_reset:
name: "factory reset"
restart:
name: "restart"
query_params:
name: query params
number:
- platform: ld2410
timeout:
name: timeout
max_move_distance_gate:
name: max move distance gate
max_still_distance_gate:
name: max still distance gate
g0:
move_threshold:
name: g0 move threshold
still_threshold:
name: g0 still threshold
g1:
move_threshold:
name: g1 move threshold
still_threshold:
name: g1 still threshold
g2:
move_threshold:
name: g2 move threshold
still_threshold:
name: g2 still threshold
g3:
move_threshold:
name: g3 move threshold
still_threshold:
name: g3 still threshold
g4:
move_threshold:
name: g4 move threshold
still_threshold:
name: g4 still threshold
g5:
move_threshold:
name: g5 move threshold
still_threshold:
name: g5 still threshold
g6:
move_threshold:
name: g6 move threshold
still_threshold:
name: g6 still threshold
g7:
move_threshold:
name: g7 move threshold
still_threshold:
name: g7 still threshold
g8:
move_threshold:
name: g8 move threshold
still_threshold:
name: g8 still threshold
light_threshold:
name: light threshold
text_sensor:
- platform: ld2410
version:
name: "presenece sensor version"
mac_address:
name: "presenece sensor mac address"
switch:
- platform: ld2410
engineering_mode:
name: "engineering mode"
bluetooth:
name: control Bluetooth
sensor:
- platform: ld2410
moving_distance:
name: "Moving distance (cm)"
still_distance:
name: "Still Distance (cm)"
moving_energy:
name: "Move Energy (%)"
still_energy:
name: "Still Energy (%)"
detection_distance:
name: "Distance Detection (cm)"
g0:
move_energy:
name: g0 move energy
still_energy:
name: g0 still energy
g1:
move_energy:
name: g1 move energy
still_energy:
name: g1 still energy
g2:
move_energy:
name: g2 move energy
still_energy:
name: g2 still energy
g3:
move_energy:
name: g3 move energy
still_energy:
name: g3 still energy
g4:
move_energy:
name: g4 move energy
still_energy:
name: g4 still energy
g5:
move_energy:
name: g5 move energy
still_energy:
name: g5 still energy
g6:
move_energy:
name: g6 move energy
still_energy:
name: g6 still energy
g7:
move_energy:
name: g7 move energy
still_energy:
name: g7 still energy
g8:
move_energy:
name: g8 move energy
still_energy:
name: g8 still energy
binary_sensor:
- platform: ld2410
has_target:
name: Presence
has_moving_target:
name: Moving Target
has_still_target:
name: Still Target
I tried TX=RX RX=TX or TX=TX RX=RX but it doesn’t work
I also encountered a problem during this process. I was wondering if it is possible to replace the RX and TX interfaces through software without having to swap hardware? I don’t know if it is possible.