I’ll gladly post some pictures. Just need to know where is appropriate.
1 Like
Thank you for asking! 
Would you mind posting the pics in the Midea discussion thread? That would be great. If I see your post popup in the other thread I’ll send @redpersian a short PM to link her/him to your new post. and ask a moderator to delete the posts in this thread!
Thanks a lot, much appreciated!
1 Like
Brand: Midea
Model: Breezeless+
Model ID: MSFA1-09N8D6-I
Year: 2022
Market: RU
Works Good.
Notes:
Huminity always 0, despite it present.
Power show room unit consumption i.e. 2-6W
External unit temperature works.
1 Like
Brand: MRCOOL
Model ID: DIY-24-HP-WMAH-230C25
Year: 2022
Market: US
Works fine!
1 Like
Brand: Carrier
Model: Extreme 42QHG012D8SX
Year: 2021
Market: GR
everything works fine
esp12f
My unit’s original dongle was 103 version and is working fine with “midea ac lan” .
1 Like
I had the opportunity to use an esp dongle as well, and it works fine!
1 Like
Brand: Senville
Model: Aura
Year: 2023
Market: CA
Model ID: SENA-18HF-Q
Power and Humidity always show 0.
1 Like
That minisplit model doesn’t have power monitoring or a humidity sensor. I just edited the esphome config and disabled those sensors.
I’m about to buy an aircon and I’m looking at the Midea Xtreme range. I don’t see it on the list. Has anybody here installed one and successfully integrated it?
I have a Senville SENA12HF and also have no Power or Humidity. However, the ‘Inquiry’ function of the remote does report both power and humidity as well as lots of other data. Not sure what this means but I would like to have them…
- Brand - MrCool
- Model - Minisplit DIY MultiZone AC/Heatpump 9k BTU
- Year - 2022
- Market - US
- Model ID - DIY-09-HP-WMAH-230C25
I’m planning on testing the 12k and 18k BTU later at some point. I believe it’s safe to say those will work as well. I plan on posting in this thread my working solution.
1 Like
Brand: Eluxe (brand of HTW)
Model: Amber R32
Year: 2023
Market: EU
Model ID: ELS071AMBR32
Power and Humidity always show 0.
“Silent” fan mode doesn’t seem to work. Fan mode changes don’t always work as expected
1 Like
Μπορείς να μου πεις περισσότερες λεπτομερείς για το logic coverter και ποσ. να το συνδεσω.
Confirmed working on ActronAir WRE-035CS Split System ~ 2020
It’s sold in Australia as ‘Australian Made for Australian Conditions’ but that may not include the control logic 
. It looks very similar to the other units listed here.
Replaced the usb connector with a wired board to a JST-XH connector and it worked great, straight to a Wemos D1 Mini Pro, no logic converter used.
I have not played too much with the extra features yet, it supports eco mode and by the looks if it, can display the power usage…
1 Like
Brand: Bryant (Carrier, Midea)
Model: 619AHBQ09XA3
Market: US
Works with SLWF-01pro, plug and play, able to update config with esphome. Humidity and Power reading don’t work.
2 Likes
Brand: Bosch
Model: Climate 3000i (CL3000iU W 26 E)
Year: 2023
Market: EU
It seems to work pretty well!
1 Like
@d3vbs Can you tell me how you configured this. I also have bluestar ac and i flashed the esphome config on nodemcu ESP8266 board. The board turns on when i turn the ac on. But in the firmware logs the ac is not responding on TX & RX ports. I already tried swapping the TX and RX pins. Is there a key combination we have to use on the ac remote to turn the wifi on ?
Works.
Brand: Senville
Model: SENL/24CD/IY
Year: 2022
Market: US
I finally go this to work after the included alexa enabled dongle was crap.
I installed this last night, tried to get it to work, gave up.
Fresh start this morning, I tried flashing it, I tried making my own yaml file and updating it. Nothing worked. After a good hour in I was ready to give up and post my results of a non working unit. Last ditch effort I power cycled the unit at the braker and presto!
1 Like
Can you tell me how did you get this work?
I have a bryant unit same as yours and got Swlf-01pro with me. I try to connect it to the USB, but don’t see any option and I Visit the address they have Mentioned. Also, I have installed Home Assistant app, but not sure how to connect it with.