Z-wave node spamming my ozw.log

Frax · December 4, 2019, 3:59pm

Hi there,
I have an issue with my z-wave network.
My node nr10 is filling my log up to 2gb of data during 24h. What I can see is that the node is receiving data all the time. ReceivedTS is constantly updating… no other node is doing that.
The thing is also that my z-wave network is extremely slow. If I press I light in the UI it can take 2-30min for the light to switch on/off.

When I unplug the node nr10 it works perfectly again. Under 1sec to switch a light on/off.

What can possibly be wrong with my node nr10? Can I edit it somehow so it stops receiving data for receivedTS all the time?

firstof9 · December 4, 2019, 4:23pm

what type of device is it?

Frax · December 4, 2019, 4:46pm

It’s a z-wave wallplug named:
“nodon_msp31xx_micro_smart_plug”

firstof9 · December 4, 2019, 4:48pm

This guy here?

Frax · December 4, 2019, 4:49pm

Yes exactly that one

firstof9 · December 4, 2019, 4:54pm

Here’s the manual:

Based on your issue it sounds like the auto-reports are set too low perhaps.
Check the configuration options 21,22,23, and 24.

Frax · December 4, 2019, 4:58pm

How do I change the configuration on my node from home assistant? I don’t understand the z-wave config parameters in configuration->z-wave

firstof9 · December 4, 2019, 5:11pm

In the zwave screen select your Node from the drop down list.
Scroll down to the Node Config Options this is the drop down where you will find 21,22,23, and 24 to configure.

Frax · December 4, 2019, 5:15pm

Ok, thanks.
I trying change nr 23 from 1000 to 20000 but it going back to 1000 when I go in once again?

firstof9 · December 4, 2019, 5:17pm

Check the ozw_log.txt to see if the value changed.

Frax · December 4, 2019, 6:01pm

Thanks now its säsong the values i set bit ut still receiving like crazy. Ser picture

Frax · December 4, 2019, 6:04pm

1million rows in log since 17.30 when I rebooted.

Here is some lines from log:

2019-12-04 18:58:28.564 Detail,
2019-12-04 18:58:28.564 Detail, Node010, Refreshed Value: old value=false, new value=false, type=bool
2019-12-04 18:58:28.564 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.564 Info, Node010, Received Meter report from node 10: Energy=14.242kWh
2019-12-04 18:58:28.564 Detail, Node010, Refreshed Value: old value=14.242, new value=14.242, type=decimal
2019-12-04 18:58:28.564 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.564 Info, Node010, Previous value was 0.000kWh, received 9893 seconds ago.
2019-12-04 18:58:28.564 Detail, Node010, Refreshed Value: old value=0.000, new value=0.000, type=decimal
2019-12-04 18:58:28.564 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.564 Detail, Node010, Refreshed Value: old value=9893, new value=9893, type=int
2019-12-04 18:58:28.565 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.565 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.594 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.622 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.668 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.702 Detail, Node010, Received: 0x01, 0x15, 0x00, 0x04, 0x00, 0x0a, 0x0f, 0x32, 0x02, 0x21, 0x64, 0x00, 0x00, 0x37, 0xa2, 0x26, 0xa5, 0x00, 0x00, 0x00, 0x00, 0x00, 0x88
2019-12-04 18:58:28.702 Detail,
2019-12-04 18:58:28.703 Detail, Node010, Refreshed Value: old value=false, new value=false, type=bool
2019-12-04 18:58:28.703 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.703 Info, Node010, Received Meter report from node 10: Energy=14.242kWh
2019-12-04 18:58:28.703 Detail, Node010, Refreshed Value: old value=14.242, new value=14.242, type=decimal
2019-12-04 18:58:28.703 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.703 Info, Node010, Previous value was 0.000kWh, received 9893 seconds ago.
2019-12-04 18:58:28.704 Detail, Node010, Refreshed Value: old value=0.000, new value=0.000, type=decimal
2019-12-04 18:58:28.704 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.704 Detail, Node010, Refreshed Value: old value=9893, new value=9893, type=int
2019-12-04 18:58:28.705 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.705 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.729 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.764 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.802 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.828 Detail, Node010, Received: 0x01, 0x15, 0x00, 0x04, 0x00, 0x0a, 0x0f, 0x32, 0x02, 0x21, 0x64, 0x00, 0x00, 0x37, 0xa2, 0x26, 0xa5, 0x00, 0x00, 0x00, 0x00, 0x00, 0x88
2019-12-04 18:58:28.828 Detail,
2019-12-04 18:58:28.829 Detail, Node010, Refreshed Value: old value=false, new value=false, type=bool
2019-12-04 18:58:28.829 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.829 Info, Node010, Received Meter report from node 10: Energy=14.242kWh
2019-12-04 18:58:28.829 Detail, Node010, Refreshed Value: old value=14.242, new value=14.242, type=decimal
2019-12-04 18:58:28.829 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.829 Info, Node010, Previous value was 0.000kWh, received 9893 seconds ago.
2019-12-04 18:58:28.829 Detail, Node010, Refreshed Value: old value=0.000, new value=0.000, type=decimal
2019-12-04 18:58:28.829 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.829 Detail, Node010, Refreshed Value: old value=9893, new value=9893, type=int
2019-12-04 18:58:28.829 Detail, Node010, Changes to this value are not verified
2019-12-04 18:58:28.830 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.860 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.901 Detail, Node010, Notification: ValueChanged
2019-12-04 18:58:28.932 Detail, Node010, Notification: ValueChanged

Frax · December 4, 2019, 6:16pm

I Think it’s working now, I put 0 (disable) as value on parameter 23. Now “receivedTS” is still no flooding
Thank you @firstof9

comatose_tortoise · January 21, 2020, 6:28pm

I’ve had the same problem with two NodOn plugs of this type. After months of use, they start spamming like this and congests the whole network. I never tried turning off energy auto report though.

Frax · January 21, 2020, 8:41pm

Try that, it still works for me

tozz · July 19, 2020, 7:44pm

I have the same issue with the same NodOn plug. Disabling all the report functions doesn’t work for me.
I think there is a firmware issue with these things.

I removed them from the network and got a Fibaro instead.