Zemismart ZM25 Zigbee howto (Tubular roller blind/shade/cover motor)

[uiguy]

Hi,

I have 5 of these and 2 of them, although saying connected in Z2M, will simply not respond when clicking up/down. They initially did all work fine, but one day, they simply stopped responding.

I can use the remote to open them, but cannot control them over MQTT,

The one I actually removed from Z2M, factory reset and then tried to join again and it won’t join again either.

UPDATE: I clicked reconfigure on the one that was still connected and now it is working again, however the other one will not join again…

UPDATE2: There is actually another one of the blinds that has stopped responding over MQTT. When I tried reconfigure again, I get:

Failed to configure 'study blinds', attempt 1 (Error: Read 0xb0c7defffefb0871/1 genBasic(["manufacturerName","zclVersion","appVersion","modelId","powerSource",65534], {"timeout":10000,"disableResponse":false,"disableRecovery":false,"disableDefaultResponse":true,"direction":0,"srcEndpoint":null,"reservedBits":0,"manufacturerCode":null,"transactionSequenceNumber":null,"writeUndiv":false}) failed (Timeout - 15870 - 1 - 30 - 0 - 1 after 10000ms) at Object.start (/opt/zigbee2mqtt/node_modules/zigbee-herdsman/src/utils/waitress.ts:63:23) at EZSPAdapter.sendZclFrameToEndpointInternal (/opt/zigbee2mqtt/node_modules/zigbee-herdsman/src/adapter/ezsp/adapter/ezspAdapter.ts:492:47) at Queue.execute (/opt/zigbee2mqtt/node_modules/zigbee-herdsman/src/utils/queue.ts:35:20) at Request.send (/opt/zigbee2mqtt/node_modules/zigbee-herdsman/src/controller/helpers/request.ts:79:20) at Endpoint.read (/opt/zigbee2mqtt/node_modules/zigbee-herdsman/src/controller/model/endpoint.ts:466:28) at Object.configureMagicPacket [as configure] (/opt/zigbee2mqtt/node_modules/zigbee-herdsman-converters/src/lib/tuya.ts:378:9) at Configure.configure (/opt/zigbee2mqtt/lib/extension/configure.ts:122:13) at Configure.onMQTTMessage (/opt/zigbee2mqtt/lib/extension/configure.ts:55:21) at EventEmitter.wrappedCallback (/opt/zigbee2mqtt/lib/eventBus.ts:174:17))

Any suggestions?

Thanks

[Micha-Btz]

Hi there,

I also plan to use two of such motors. Did you have any clue if it will now work with ZHA?
There are also experiences with the quality especially the battery.

Thanks Micha

[Mr.ToR (Tonguç Endem)]

Hi,

You should be able to check ZHA compatibility of most stuff from here.

Database of Zigbee devices compatible with ZHA, Tasmota, Zigbee2MQTT, deCONZ,...

Also here you can find most zigbee devices and what integration they use:
https://zigbee.blakadder.com/all.html

[deblynprado]

Thank you so much!

Your scripts helped me to setup my ZM25!
It’s my first and I bought without the remote control

[mauritsivs]

OMG thank you for this! this worked flawlessly…well…just upper and lower limit are inverted, because direction of my roller is reversed (and even when setting direction reversed with that second script it still is inverted) but thats just an easy edit in your script!
(i have ZM25TQ)
thanks again

[Maikai (Mike)]

Hi,

about to get these motors. been reading here, as I understand you are unable to control the position of the blind motors without setting the limits first manually? Before being able to control them in HA?

Thanks.

[currest2620 (Steven Curren)]

I have just installed three of these motors and I can report that they work very will with Zigbee2MQTT.

Just having trouble pairing the 9 channel remote to the correct roller blind though (I seem to have three blinds on channel 1 instead of the blind I want to have). Not sure if I can reset the remote back to factory settings.

PS: I found I was able to set the upper and lower limits of the blinds via the MQTT device page. No option for the mid setting though, that needs to be set via the remote.

[brian9 (Brian)]

Hi,

Did you ever happen to resolve this issue? 2 of my 7 roller blind motors are experiencing this issue. They work fine with the FR report and pair to ZHA successfully, however when issuing an open/close command, ZHA the motors do not respond. HA does log that the command was sent.

thanks!

[Micha-Btz]

does anyone know something similar for an outside marquise? Maybe also with battery but waterproof?

[DJAMIRSAM]

Hey so i just purchased one of these ZM25-ZB from them and in Z2MQTT it shows as Zigbee Model
TS0601
Zigbee Manufacturer
_TZE284_fzo2pocs

and says unsupported, does anyone have any idea on how to add support?

External Definition if needed

const definition = {
    zigbeeModel: ['TS0601'],
    model: 'TS0601',
    vendor: '_TZE284_fzo2pocs',
    description: 'Automatically generated definition',
    extend: [],
    meta: {},
};

module. Exports = definition;

What I have in based on the Z2MQTT Documentation and ZM25 Config

const {} = require('zigbee-herdsman-converters/lib/modernExtend');
// Add the lines below
const fz = require('zigbee-herdsman-converters/converters/fromZigbee');
const tz = require('zigbee-herdsman-converters/converters/toZigbee');
const exposes = require('zigbee-herdsman-converters/lib/exposes');
const reporting = require('zigbee-herdsman-converters/lib/reporting');
const ota = require('zigbee-herdsman-converters/lib/ota');
const utils = require('zigbee-herdsman-converters/lib/utils');
const globalStore = require('zigbee-herdsman-converters/lib/store');
const e = exposes.presets;
const ea = exposes.access;

const definition = {
    zigbeeModel: ['TS0601'],
    model: 'TS0601',
    vendor: 'Zemismart',
    description: 'Tubular motor',
    fromZigbee: [legacy.fz.tuya_cover, fz.ignore_basic_report],
    toZigbee: [legacy.tz.tuya_cover_control, legacy.tz.tuya_cover_options, legacy.tz.tuya_data_point_test],
    exposes: [e.cover_position().setAccess('position', ea.STATE_SET)],
    extend: [forcePowerSource({powerSource: 'Mains (single phase)'})],
};

module. Exports = definition;

[JonAxel]

Continuing the discussion from Zemismart ZM25 Zigbee howto (Tubular roller blind/shade/cover motor):

Hi, I’m having trouble getting this to work. I get this “repair message” when i run the action.
Can you help me with this?

[fanuch]

I’m new to the party and also tried the script to receive the same message.

Note that according to this reply, the script is not actually needed!

@currest2620

PS: I found I was able to set the upper and lower limits of the blinds via the MQTT device page. No option for the mid setting though, that needs to be set via the remote.

I have confirmed that I can set the lower limit, but for some reason the upper limit is not working.

My workflow:

• Press down
• Press stop at desired position “down” position
• Select the “Border” dropdown; and
• Select “down” (beeps in response)
• Press up
• Press stop at desired “up” position
• Select the “Border” dropdown; and
• Select “up” (beeps in response)

Then when I pressed “down”, it stopped successfully at the position I had set.
When I pressed “up” it didn’t stop and jarred my finger until I pressed “stop”

Will continue testing soon …
Setting upper and lower limit works.

NOTE when in “reverse direction → back” the Border directions are reversed.
I.e I had to set “up” at the bottom and “down” at the top.

Works perfect though!!!

[mondalaci (László Monda)]

I purchased this Zemismart Zigbee Roller Shade on AliExpress.

According to the ZHA device info section:

• TS0601
• by _TZE200_fzo2pocs
• Quirk: zhaquirks.tuya.ts0601_cover.TuyaZemismartSmartCover0601_3

I don’t have a remote and don’t want to install Zigbee2MQTT, but there are some relevant attributes in ZHA:

I’ve set some attributes; the roller sometimes stopped in various positions. However, it doesn’t seem to remember them, and I’m unsure which attribute to set to which values for the up/down position.

Thanks in advance!

[rohanking (Rohan)]

Just in case anyone needs to reset the limits (In trying to set the limits on mine, I somehow made the upper and lower limites the same. you can use 106

bool,106,1 - reset limits

[nickshanks (Nick)]

Hi,

All tutorial videos I’ve seen online (as well as the instructions) show the blind as having a slot so the crown/end plug can ‘grip’ the blind. Would these work for me?

[rewrew]

@nickshanks

I have just purchased three units from this. I have some Ikea roller blinds, and the tube is very low quality and when the motor is inserted it turns free, so it does not work.

To fix it, in the small ones, that had a cardboard tube, I had to increase a bit the width of the motor by adding a bit of electrical tape.
In the longer ones, that have a metallic tube, I had to press it with some pliers to deform it enough so the motor engages.

Maybe this can help you.

[digiwolf]

Hi there – I have two Zemismart Rollers (Zigbee: _TZE284_fzo2pocs) installed through Zigbee2MQTT. I installed the script based on @ndbroadbent, however I receive the following error:

Any ideas what I am doing wrong?

[Mr.ToR (Tonguç Endem)]

Hi @nickshanks,

I’m not quite sure if it would work. The issue is if there would be enough friction.
Just to avoid this kind of issues, I bought my motors first, then while buying the shades, I took a motor with me and agreed on an almost compatible profile. Finally, I had to cut a small piece of the plastic on the motor to make it fit the profile the shade/blind guy was using. I would think there would be a lot of torque when the shade is completely down. Not sure if it work properly only depending on friction. You see, if it would slip just a tiny bit, you would have bigger problems in time.

[Spiffo]

Brilliant! Thanks so much, works like a charm.

[Micha-Btz]

I have installed an paired my motor successfully, but one problem.
It is rotated in HA, so this means HA think the rollo is closed, but in real it is open.
Can I cahange the behaivior of HA?

Here is the solution

Zigbee blinds displays backwards frontend

I have ZCM03 shades (TZE200_vdiuwbkq TS0601), below worked for me with ZHA: Click Manage zigbee device In clusters tab pick TuyaWindowCoverControl Then pick attribute cover_inverted, set value “Bool.true”, click “write attribute” button Then pick attribute motor_direction, set value “Bool.true”, click “write attribute” button Reload zigbee integration You might need to full open/close shades once in HASS to synchronize some state. For some reason both cover_inverted/motor_direction need to be…