ZHA Failed to Set Up

[Luke1 (Luke D)]

Hello I am Struggling to Get ZHA working, It was working and then I tried to get Zigbee2MQTT but couldnt get it working so I went back but ever since then I can not getting ZHA working again.

Logger: zigpy.application
Source: /usr/local/lib/python3.9/site-packages/zigpy/application.py:73
First occurred: 09:06:08 (1 occurrences)
Last logged: 09:06:08

Couldn't start application

Logger: homeassistant.config_entries
Source: components/zha/core/gateway.py:152
First occurred: 09:06:08 (1 occurrences)
Last logged: 09:06:08

Error setting up entry CP2102N USB to UART Bridge Controller, s/n: Correct Serial Number - Silicon Labs for zha
Traceback (most recent call last):
  File "/usr/src/homeassistant/homeassistant/config_entries.py", line 304, in async_setup
    result = await component.async_setup_entry(hass, self)  # type: ignore
  File "/usr/src/homeassistant/homeassistant/components/zha/__init__.py", line 102, in async_setup_entry
    await zha_gateway.async_initialize()
  File "/usr/src/homeassistant/homeassistant/components/zha/core/gateway.py", line 152, in async_initialize
    self.application_controller = await app_controller_cls.new(
  File "/usr/local/lib/python3.9/site-packages/zigpy/application.py", line 69, in new
    await app.startup(auto_form)
  File "/usr/local/lib/python3.9/site-packages/zigpy_znp/zigbee/application.py", line 196, in startup
    return await self._startup(
  File "/usr/local/lib/python3.9/site-packages/zigpy_znp/zigbee/application.py", line 255, in _startup
    await self._write_stack_settings(reset_if_changed=True)
  File "/usr/local/lib/python3.9/site-packages/zigpy_znp/zigbee/application.py", line 1129, in _write_stack_settings
    current_value = await self._znp.nvram.osal_read(
  File "/usr/local/lib/python3.9/site-packages/zigpy_znp/nvram.py", line 173, in osal_read
    raise KeyError(f"NV item does not exist: {nv_id!r}")
KeyError: 'NV item does not exist: <OsalNvIds.CONCENTRATOR_ENABLE: 50>'

Logger: homeassistant.config_entries
Source: components/zha/core/gateway.py:152
First occurred: 09:06:08 (1 occurrences)
Last logged: 09:06:08

Error setting up entry CP2102N USB to UART Bridge Controller, s/n: 5e937cc6fe93eb11a4cda75b3d98b6d1 - Silicon Labs for zha
Traceback (most recent call last):
File “/usr/src/homeassistant/homeassistant/config_entries.py”, line 304, in async_setup
result = await component.async_setup_entry(hass, self) # type: ignore
File “/usr/src/homeassistant/homeassistant/components/zha/init.py”, line 102, in async_setup_entry
await zha_gateway.async_initialize()
File “/usr/src/homeassistant/homeassistant/components/zha/core/gateway.py”, line 152, in async_initialize
self.application_controller = await app_controller_cls.new(
File “/usr/local/lib/python3.9/site-packages/zigpy/application.py”, line 69, in new
await app.startup(auto_form)
File “/usr/local/lib/python3.9/site-packages/zigpy_znp/zigbee/application.py”, line 196, in startup
return await self._startup(
File “/usr/local/lib/python3.9/site-packages/zigpy_znp/zigbee/application.py”, line 255, in _startup
await self._write_stack_settings(reset_if_changed=True)
File “/usr/local/lib/python3.9/site-packages/zigpy_znp/zigbee/application.py”, line 1129, in _write_stack_settings
current_value = await self._znp.nvram.osal_read(
File “/usr/local/lib/python3.9/site-packages/zigpy_znp/nvram.py”, line 173, in osal_read
raise KeyError(f"NV item does not exist: {nv_id!r}")
KeyError: ‘NV item does not exist: <OsalNvIds.CONCENTRATOR_ENABLE: 50>’

[le_top]

@Luke1

zigpy_znp

You mention Silicon labs, which is the manufacturer of your UART/USB bridge.

zigpy_znp is for Texas Instruments - in most cases you’ld be using a device that has USB onboard, which means they do not require a bridge. If you were using a TI CC2530 you’ld require a bridge, but the CC2531 already has USB which is what you’ld buy on a USB stick.

I suppose that you did not make the right choice somewhere. What hardware do you have?

[Luke1 (Luke D)]

Hello,

Thankyou so much for your reply. I am using the new Sonoff ZigBee 3.0 the Balck one in the metal case. When I first started it allowed me to select which device to use. I am not sure why as it does show up as connected but the ZHA does not seem to open anymore.

[Luke1 (Luke D)]

When I enter it manually I get a failed to Connected the with /dev/ttyUSB0 - CP2102N USB to UART Bridge Controller, s/n: 5e937cc6fe93eb11a4cda75b3d98b6d1 - Silicon Labs
as the Serial device path,

Keep the Port Speed the same like in the doucmentation and data flow control as hardware

I am following the these instructions How to add Zigbee devices to Home Assistant via SONOFF Zigbee 3.0 USB Dongle Plus? How to flash firmware to Cc2652P? - SONOFF Official

[metropt]

Did you fix this?

[Samuele_Sommariva]

Try unscrewing the antenna during setup… It made no sense to me, and maybe it is not the solution.
While I was checking the logs there was a line that said something like

“noisy radio environment: try to uscrew the antenna before the network is completed”

(I didn’t copy it and I cannot find it again).
I removed the antenna and the installation went through.

[yousuf]

did you get the solution ?
I am having the same issue. the first time was working fine and added few devices.
when I waked up on the morning I get the same error. ZHA is not recognizing the USB bridge.
I have tried to
delete & re-install ZHA
Reboot HA
change USB port
unplug the USB attena

nothing work

[xchen326]

I ran into the same issue ever since 2022.04. Since I always had issue with my Ikea remote side button not working properly wanted to move to Z2M, I used this opportunity to redo my entire zigbee network.

Everything is working properly without any issues.

[yousuf]

I was able to fix this issue by re-flashing the USB Firmware.

[Hedda]

Be sure to use USB extension cable with longer plug that is on the adapter itself for proper connection.

To avoid EMF interference strongly recommended buy and use → Long USB extension cable

• Another reason for using a USB extension cable is that the USB-plug design of ITead’s Sonoff Zigbee 3.0 USB Dongle Plus hardware adapter is a little short which makes it harder and sometimes impossible to plug it into some USB ports if the computer enclosure/chassis/casing is to thick around the USB-port as that will physically prevent the USB dongle from actually making a proper connection inside the USB port even if it looks like it is plugged in all the way that is possible.

ITead's "Sonoff Zigbee 3.0 USB Dongle Plus" (model "ZBDongle-P") based on Texas Instruments CC2652P +20dBm radio SoC/MCU

UPDATED! The announced TI CC2652P based “Sonoff Zigbee 3.0 USB Dongle Plus” from ITead, later renamed to “ZBDongle-P”, has been released and looks to be great value for a premium hardware package sold for a low price. It is based on Texas Instruments CC2652P radio chip and this “ZBDongle-P” variant is to be sold side-by-side as an alternative to their new “ZBDongle-E” variant that is instead based on Silicon Labs EFR32MG21 radio SoC chip, and while both practically have the same specifications o…

[IbRuthless]

Hi,

My Zigbee Home Automation intergration stopped working a few days ago, I could’t rectiy the problem so decidd to remove and start again. I’ve tried adding the Zigbee Home Automation intergration again, but for some reason I cannot connect .

I’ve set the path: socket://[MY IP]:8888 and port to 115200 but it fails to connect.

Any ideas?

[bgalito]

Hi,

Did you find a solution? I have the same issue.

[IbRuthless]

No, I ended up buying the Sonoff Universal Zigbee 3.0 USB Dongle Plus.

No issues with this device, been in over 3 weeks no issues.

[Iuliansok]

The same is for me cannot set up nothing and it was working fine until update

[blizzrdof77 (Ben Wagner)]

I had this issue suddenly after restarting today, and it scared me straight! I am using the ConBee II USB Gateway with a USB 2.0 extension cable on a BeeLink GK55 mini computer running HAOS (Generic x86-64).

Thankfully, I was able to resolve my issue by changing to a different USB 2.0 port on my HASS host machine.

The one I was using was also USB 2.0, so perhaps it just needed to be secured, or maybe it was the port.

[gerardsamara]

Hello,

I have a mini PC Beelink U55 and this happened sometimes with the Conbee 2 USB dongle.

The fix ( workaround) was to unplug -replug the usb dongle and reboot

[ariagha (Ari benagha)]

Hi
I have samee issue , any solution?

[Ars4l4n (Arsalan)]

reflash the firmware of what?