Hello,
The alarm_level and alarm_type codes are readily available in the forums for the Kwikset 916 (non zwave+) models. Has anyone figured out the access_control codes for the Kwikset 916 zwave plus model? Not sure if it matters or not, but I am looking for codes related to the OZW Beta integration.
Thanks in advance!!!
They should be the same.
Are you sure? Several differences. Like the Zwave plus model has an entity for replace battery now and soon where as the zwave model has codes for low, critical and too low to operate. Also, many of the acces_control codes are different. The zwave plus model uses 1-6 and 11 whereas not the case with the zwave model.
Access Control and Alarm Type are different types of notices, so the values will be different. One is v1 and one is like v4 (I don’t fully recall).
Sorry, maybe I worded my question incorrectly. I guess what I am looking for then is the access_control values so I can set up automations similar to the ones I had for Alarm Type with my non zwave+ models.
I was able to pull it from the SDS XML from SiLabs, here’s your codes:
| Friendly Name | Hex Value | Number |
|---|---|---|
| Manual lock operation | 0x01 | 1 |
| Manual unlock operation | 0x02 | 2 |
| RF lock operation | 0x03 | 3 |
| RF unlock operation | 0x04 | 4 |
| Keypad lock operation | 0x05 | 5 |
| Keypad unlock operation | 0x06 | 6 |
| Manual not fully locked operation | 0x07 | 7 |
| RF not fully locked operation | 0x08 | 8 |
| Auto lock locked operation | 0x09 | 9 |
| Auto lock not fully locked operation | 0x0A | 10 |
| Lock jammed | 0x0B | 11 |
| All user codes deleted | 0x0C | 12 |
| Single user code deleted | 0x0D | 13 |
| New user code added | 0x0E | 14 |
| New user code not added due to duplicate code | 0x0F | 15 |
| Keypad temporary disabled | 0x10 | 16 |
| Keypad busy | 0x11 | 17 |
| New program code entered : unique code for lock configuration | 0x12 | 18 |
| Manually enter user access code exceeds code limit | 0x13 | 19 |
| Unlock by RF with invalid user code | 0x14 | 20 |
| Locked by RF with invalid user code | 0x15 | 21 |
How would you go about finding these codes for a Kwikset 914 Z-Wave lock? I have both a 916 and 914 so this is awesome mind you 
They’re all the same if you’re lock is newer.
But the 914 doesn’t have usercodes; it’s just a deadbolt.
Does your lock have Access Control sensor or Alarm Type sensor?
Alarm Type I believe.
These are the only codes I’m aware of for locks and the alarm_type sensor.
| Code | Status |
|---|---|
| 0 | No Status Reported |
| 9 | Lock Jammed |
| 17 | Keypad Lock Jammed |
| 18 | Keypad Lock |
| 19 | Keypad Unlock |
| 21 | Manual Lock |
| 22 | Manual Unlock |
| 23 | RF Lock Jammed |
| 24 | RF Lock |
| 25 | RF Unlock |
| 26 | Auto Lock Jammed |
| 27 | Auto Lock |
| 32 | All Codes Deleted |
| 33 | Code Deleted |
| 112 | Code Changed |
| 113 | Duplicate Code |
| 161 | Bad Code Entered |
| 162 | Lock Code Attempt Outside of Schedule |
| 167 | Battery Low |
| 168 | Battery Critical |
| 169 | Battery Too Low To Operate Lock |
This is great! Thanks so much 