That’s unfortunate, but thanks
C05 - ESP-C3-C05 ESP32-C3 4Mb Module (DT-ESP-C05) Configuration for Tasmota
CBU - CBU Module Datasheet-Tuya IoT Development Platform-Tuya Developer
Yep, saw the datasheets before this, since you have C05 in hand.
Could you take a picture C05 next to CBU chip?
Just need to gauge the size and pins
i don’t have CBU , only i have a ZMAI 90 with CBU on him, when i will open zmai i will post a picture
Hey all!
I see you’re having issues with non-ESP chips. I think I might have a solution for that. My solution is still very WIP and in early stages of development, but supports Home Assistant right now, at least for relays and PWM leds. TuyaMCU and more is coming soon.
I am working on Tasmota-like firmware replacement for new Tuya chips, which right now supports 3 platforms:
- BK7231T (WB2S, WB3S, WB2L, etc)
- BK7231N (CB2S, CBU, etc)
- XR809 (XR3)
The goal of the project is to add easy Home Assistant and other platforms support for all Tuya devices, without doing ‘brain transplant’ procedure (replacing old chip with ESP).
W600 platform support is also possible.
Please see my related articles here:
https://www.elektroda.com/rtvforum/topic3866123.html
Also, check out my CCWFIO232PK BK7231T step-by-step flashing guide (it was ESP before but now changed to Bekken…):
https://www.elektroda.com/rtvforum/topic3875654.html
Also check out this Qiachip Smart Switch BK7231N/CB2S guide:
https www elektroda com/rtvforum/topic3874289 html
(sorry I can’t post more than two links)
9 Likes
Good job!
Now, what would be nice is if it allowed OTA flashing from the stock Tuya rubbish like Tuya-Convert used to…
1 Like
There’s cloudcutter for that, probably another 25 days left before the tools are released
3 Likes
I purchased some of the modules from this site that were advertised as DMP-L1 modules but have a different profile and are marked XH-001B.
What was delivered looked correct but the pinout was different and it turns out that it is an ESP32 version with a part number of XH-004B…
Has anyone had a play with one of these modules ??
Gaz
That’s new? Were you able to get it into flashing mode?
Not yet, I have traced the pinout to the edge connector as best I can with everything covered with white silkscreen and the labels on the edge connector seem to be correct.
The RST terminal is connected to Pin 9 of the ESP and I have to check if this pin is pulled up on he module or if I need to do that as the ESP32 data sheet shows it as a chip enable.
A friend with a wechat account is going to ask sparkeiot for some info.
Gaz
OK, fried the first one somehow but the second one is working. Used the normal power up with GPIO0 tied low to get it into flash mode.
One issue I have is that it won’t connect to the closest of my Unifi APs, I get this error:
Event: Disconnected ssid=‘ssid’ bssid=[redacted] reason=‘4-Way Handshake Timeout’
It connects fine to the other Unifi AP which happens to be on an older firmware, the one that doesn’t work is up to date. I have never had this issue with any other Esphome device but all have been ESP8266.
My mate got a pinout diagram from Sparkleiot but the manual they provided was for a different module.
Gaz
2 Likes
How did the first one got fried?
By not paying attention to what wire I plugged in where on my prog adapter !!
1 Like
Hi guys, any advice on how can i desolder this wb2l in an encased silicone?
Normally, if i apply some heat gun, it would take less than 30 seconds (with the pcb removed) to remove the tuya module.
But this one is not budging even with 1 minute and slightly more, i’ve failed with my first attempt since i accidentally ripped off the pads.
So i’m trying to be extra cautious this time
I’ve also just purchased the Moes Smart Garage Door Opener (Aliexpress) and they’ve changed the model number to MS-102. Inside it contains the WB2S chip which is not flashable to my knowledge.
Deslodered it and ordered a few TYWE2S from one seller, and ESP-02S chips from another to try and replace it with and hopefully load tasmota onto it.
Cloud clutter was a coordinated release, Tuya was informed of the exploit beforehand (and actually paid a bounty over it) and has already patched it before the exploit was released to the public. So unless you are still on older firmware, it won’t work.
Correct, so don’t update your tuya firmware guys
Just waiting for that write up for flashing custom firmware
Esp-02s should be enough and cheaper,
I’ve already swapped a few WB2L (on plug with power monitoring) with that.
1 Like
I was interested to see this Moes WiFi Smart Switch with a model number as posted in
I ordered one though Ali Express last June. but only tried to pair it last month. It has no model number and is very different. After many pairing failures with Smart Life I was able to get it to pair when only 50 cm from the router. After pairing I got a firmware update notification, but it didn’t complete and after powering off and on again, it will not pair and remained offline.
I suspect the firmware is corrupted and have been looking to see if there is a way I can try to update the firmware, or use other firmware. Updating this type of firmware is new to me and I have just acquired a CH340 USB to Serial adapter. My problem is that the WA2 chip seems to be less common than those on Sonoff and there is no simple way to plug in or attach a header. This brought me to this page that has information about it incuding a photo of the back side of the WA2 in post No. 6 that is identical to my device.
I am now looking for pointers on how to proceed to connect to the device and what to do after that. I would be satisfied to restore the original firmware, but Moes ignores requests to provide information about it, or the pinout.
